MGP Style Gates

From Safety Third Racing Wiki
Jump to: navigation, search

Major shout out to Smitty for all these awesome drawings/designs!


Contents

Gate Types

Gate Name Looks Like General Printable Area Dimensions
G30 Gate1.png Outside Panel Dimensions
( 1 X Top = 3.5', 2 X Sides = 30")
Inside Space ( 30" X 30" )
G30-Spec.png


G75 Gate1.png Outside Panel Dimensions
( 1 X Top = 7', 2 X Sides = 5')
Inside Space ( 5' X 5' )
G75-Panel-Diagram-v1.png
G96 Gate1.png Outside Panel Dimensions
(1 X Top = 9', 2 X Sides = 6')
Inside Space ( 7' X 6' )
G96-Panel-Diagram-v1.png
D1010 10X10-DropGate.png Outside Perimeter
(10' X 10')
Inside Space ( 7' X 6' )
D1010-Panel-Diagram-v3.png

Ground Gate 7 X 5 MultiGP Panel

Outside Panel Dimensions (Top = 7'X 1', Sides = 1' X 5')

Inside Space ( 5' X 5' )


Gate1.png Gate1explode.png

Qty Item
6 1" SCH40 PVC Pipe x 39.5"L
2 1" PVC Elbows*
3 1" PVC Connectors
2 1/4" zip ties
2 3/4" x 36" Stake or rebar


Ground Gate 7 X 5 MultiGP Panel (No Elbows)

Outside Panel Dimensions (Top = 7'X 1', Sides = 1' X 5')

Drill holes at the ends of the PVC that slide into the TOP Panel and use zip ties to make the connection. By using zip-ties instead of elbows, the gate breaks down to 40" for easy transport, or easily folded 'as is' for faster storage. Also, repairs are quick and cheap!


Inside Space ( 5' X 5' )

Ziptie3.png Ziptie2.png Ziptie1.png

Qty Item
6 1" SCH40 PVC Pipe x 39.5"L
4 1/4" Zip Ties
3 1" PVC Connectors
2 3/4" x 36" Stake or rebar

Ground Gate 9 X 6 MultiGP Panel

Outside Panel Dimensions (Top = 9' X 1', Sides = 1' X 6')

Inside Space ( 7' X 6' )


9x6-1.png 9x6-2.png

Qty Item
2 1" SCH40 PVC Pipe x 51.5"L
2 1" SCH40 PVC Pipe x 41.5"L
2 1" PVC Elbows*
2 1" PVC Connectors
2 1/4" zip ties
2 3/4" x 36" Stake or rebar
* Large Zipties can replace the elbows if holes are drilled at the ends of the PVC

Raised Gate

Gate2.png Gate2explode.png

Qty Item
10 1" SCH40 PVC Pipe x 39.5"L
2 1" PVC Elbows
2 1" PVC Tees
4 1" PVC Connectors
4 1/4" zip ties
2 3/4" x 60" Stake or rebar

270 Degree Upper/Lower 7x5

270-1.png 270-2.png

Components are essentially a standard gate + raised gate + 2 Tees & 2" connector

Note: More rope may be necessary if 10' rebar is not used

Qty Item
16 1" SCH40 PVC Pipe x 39.5"L
1 1" SCH40 PVC Pipe x 2"L
3 1" PVC Elbows
3 1" PVC Tees
8 1" PVC Connectors
6 1/4" zip ties
2 3/4" x 120" Stake or rebar
2 3/4" x 30" Stake or rebar
3 Rope Stakes
1 40' rope

Low Panel

This low panel is used for marking areas such as the landing zone

LowPanel.png

Qty Item
2 1" SCH40 PVC Pipe x 39.5"L
2 1" SCH40 PVC Pipe x 20"L
2 1" PVC Elbows
1 1" PVC Connectors
2 3/4" x 24" Stake or rebar

7 X 5 Dive Gate

This dive gate is made from standard 7x5 gate panels + 1 extra top section

DiveOverview.png

The thin SCH10 pipe is used to make the box to keep the weight down. The gates will keep tension on the box to keep it together. Tees go on higher side, 3-ways on lower.

DiveUpper.pngDiveLower.png

Drill holes in the Tees as shown. Glue 90deg elbows to 20" Pipe. Drill hole in end of 20" approx 1.5" from end away from elbow, on the top side. Run a zip tie thru the Tee and pipe. It will help that this connection can rotate while assembling.

Qty Item
4 1" SCH10 PVC Pipex 79"L
2 1" SCH40 PVC Pipe x 79"L
6 1" SCH40 PVC Pipe x 39.5"L
2 1" SCH40 PVC Pipe x 20"L
2 1" SCH40 PVC Pipe x 2"L
2 1" PVC 90 Elbows
2 1" PVC Tees (hole drilled in center)
2 1" PVC Side Outlet Elbows (3-way)
2 1" PVC 45 Elbows
4 1" PVC Connectors
2 3/4" x 36" Stake or rebar
2 3/4" x 60" Stake or rebar

10 X 10 MGP Spec Dive Gate

enjoy the destruction of your quads

Photos of Build here -> https://flic.kr/s/aHsm3MmEBE


MGPdrop.png

10X10-DropGate.png

Qty Item
6 1" EMT Conduit x 120"L
1 1" EMT Conduit x 118"L
4 1" EMT Conduit x 92"L
2 1" EMT Conduit x 87"L
2 1" EMT Conduit x 61.6"L
2 1" EMT Conduit x 24.4"L
8 1-3/8" Tee
2 1-3/8" Elbow
2 1-3/8" 3-way 102deg corner